6. Mount on the wall

Transmission Box Installation
(1) Insert the transmission box into the carrier base until you heard the sound 'CLICK'. The red button will lock the transmission box automatically. Check if the box was installed properly.
(2) Pull the red pad and then draw out the transmission box as figure 8.
(3) Insert the infar red light receiver into the port. The infar red light receiver should face the room, as show in figure 9.
(4) Connect the adaptor to the supply of electricity and the transmission box.
(5) Hand up the curtain properly.

Adjust the tension of the wire
(1) Using the control pad (figure 11) to operate the system. The curtain will move smoothly even the carriers passing the connection point of the track.You have to adjust the tension of the wire if the curtain can not stop automatically when it is fully opened/closed.
(2) Use the wrench to turn the hexagon bolt clockwise until the curtain can stop automatically within 2 seconds when it is fully opened/closed. The hexagon bolt is located at the end of the main track.
If the motor cannot stop in 2 seconds when the curtain is fully opened/closed even the hexagon bolt has been adjusted to the top end position. You have to release the hexagon bolt anti-clockwise to the lowest position, do not loose out the bolt from the base track, then loosen the big head screw on carrier "A" on half way as shown in figure 1, and pull the wire until it is taut and fasten the screw on carrier "A" again.
Repeat procedure "(2)" until the curtain stop automatically within 2 seconds when it is fully opened/closed.
(3) Fasten all the screws and cut off the extra wire.

Track assembly for One Way Applications
(1) Undone the wire and remove the twists from the wire. Also uncoils the wire carefully.
(2) Loosen the big screw on carrier "A" to the half way as shown in figure 1.
(3) Loosen the small screw on the carrier "B" to falf way as shown in figure 2.
(4) Loosen the fasten screw at the end base, with the pulley system, then take the end base out of the track carefully in the direction along the track. The wire will go along with the end base.( The plastic pulley does not remain in the track except the side of Bigger Carrier "A".)
Make sure not to twist and coil the wire. See figure 3 and figure 4. Since the wire is enough length to go along with the end base.
(5) Pull the small carrier "B" out of the track, unscrew the nut that is located at the bottom of the carrier"B" and loosen the screw on the top of the carrier "B".
(6) With pliers, grab out the wire gently, and then you can take out the smaller carrier "B" from the wire. Take out the entire plastic pulley simultaneously.
(7) If you wanted to add the pulley on the side of Bigger carrier "A", pull out the Bigger carrier "A" from the track very careful, Then insert the pulley into the track one by one according to your requirement.(recommend one pulley for every 12cm.)
Make sure not to twist and coil the wire. See figure 3 and figure 4. Since there is enough length for the wire will go along with the end base.
(8) Place back the Bigger carrier "A" into the track carefully, push the end base into the end of the added track and fasten the screw on the end.
(9) Pull the wire until it is taut and fasten the screw in bigger carrier "A".
(10) Adjuest the tension of wire (procedure 3.3) until the curtain stop automatiaclly within 2 seconds when it is fully opened/closed.

Switch Control Setting
Warning: The infar red light receiver is specific designed only for this remote control window treatment system. The receiver cannot be used or modified for other uses. The receiver needs two batteries to operate.
Curtain No.1 can be set by switch the switch control 1 to ON and all others set to OFF. Other curtain number setting is similiar with different numbers of ON and OFF. By default, the switch is set to 8 when delivery. Figure 10 shows the switch control.